The guide will explain the installation of Hisense Laser TV, from wall mounting the brackets to screen alignment, in a crystal clear way. So, if you have bought a new Hisense Laser TV for your home, then you need to stick with this guide. Moreover, this guide will provide you with details on the required hardware components and the tools to install the Laser TV for the first time. So, have a look at the guide and complete the installation process without complications.
Things to Be Done Before You Setup Hisense Laser TV!
Follow the upcoming session and get ready with the necessary components and tools beforehand to undergo the Hisense Laser TV installation process smoothly.
- Unbox the Hisense Laser TV package and separate the tools and the TV screen.
- Place the TV screen in a suitable place without any disturbance.
- Get the necessary cables, including the Power cord and HDMI.
- Clean the remote control and insert it with fresh batteries.
Essential Hardware & Parts List
| Long side inner frame pieces (A1 & A2) | Long side outer frame pieces (Q1 & Q2) | Short side inner frame pieces |
| Long side inner frame connectors and screws | Inner frame connectors and screws | M6 × 6 inner frame corner screws |
| Vertical beam | Vertical beam cover plates and screws | Screen |
| Protective sheet | Fiber rods (long & short) | Pull pin nuts |
| M4 × 45 pull pin screws | Long-side pull rods | Short-side pull rods |
| Outer frame connectors | Outer frame splicing connectors | Short-side outer frame pieces |
| M3 × 6 outer frame connector screw | Cushion blocks | Hanging brackets |
| Adjusting rods | Connecting rods of hanging bracket | Plastic expansion pipes and screws |
| M4 hexagon socket screwdriver | M3 hexagon socket screwdriver | Gloves |
Essential Tools List
| Tape measure | Electric drilling machine | Hammer |
| Woodworking pencil | Screwdriver | Level ruler |
| Stud finder |
Procedure for Installing Hisense Laser TV
Once you are done with the above prerequisites, follow the upcoming step-by-step instructions to complete the installation process. You can use these installation steps for any Hisense Laser TV, including the L5 and L9 models.
- As an initial step, make sure you are ready with the necessary tools, as mentioned in the above table.
- Next, prepare the wall space to mount your laser TV. Use a tape and measure the wall space (height & width) according to your TV screen.
Tip! For an optimal viewing experience, I recommend having a minimum viewing distance of 3m.
- Then, take a long TV stand that is equal to the size of the smart TV. Place the TV stand on the floor where you are mounting your Hisense TV.
- Next, you need to install the mounting brackets. To do that, take the necessary parts from the tools package.
- Get the measuring tape, measure 1489 mm from the top of the TV stand, and mark it. Further, mark another hole horizontally towards the right with a distance of 830 mm and mark it.
- From the two holes, measure 175 mm vertically above and mark a hole, respectively.
- Now, use a drilling machine and make four holes in the marked places. It is recommended to use an 8 mm diameter drill bit for better and safer results.
- Use the hammer and drill the bolts into the respective holes.
- Next, grab the brackets and install them with the necessary screws and tighten the brackets firmly without any gap.
- Now, install the wands with the desired screws and then hang the wands onto the brackets. Make sure to hang the long wands above and the short wands at the bottom. Further, hang the handles onto the wander.
- As a next step, wear gloves on your hands and grab the TV screen. Hang the Laser TV screen into the brackets and check the screen. Ensure it’s seated properly.
- Once done, you need to configure the Laser TV screen alignment. So, power on your Hisense Laser TV and fetch the remote controller.
- Launch the Settings section of your TV and configure the Network Settings under the Network section.
- Further, get back to the Settings menu and scroll down to select the System option.
- Hover to choose Projector Settings and hit the Geometric Correction option. You need to confirm the selection by tapping the Confirm button.
- Then, get your smartphone and connect it to the same WiFi with which your Laser TV is connected.
- Now, you will be prompted with an on-screen instructions. Follow them correctly to adjust the position of your Laser TV console within the screen range.
- Get your desired smartphone and scan the QR code displayed on the TV screen. Then, click the “+” icon to activate the camera.
- Use your smartphone camera to take a picture of the Laser TV screen. Upload it on your smartphone and hit the Finished option on your TV screen to complete the process.
- Finally, the Hisense TV home screen will appear. From there, search for the necessary content and stream it on your TV screen with good quality.
End Note!
Once you have finished setting up your Hisense Laser TV, you can enjoy watching your favorite content in a 4K Ultra HD quality with HDR function. Moreover, you can stream the content via a laser display and use Dolby Atmos audio technology to get the best theatre experience now in the comfort of your home.
